Product ID:CADWELD ELECTRICAL WELDING MATERIAL
MSDS Date:03/20/1991
FSC:3439
NIIN:00-196-6125
Status Code:A
MSDS Number: CKLQY

ERICO PRODUCTS INC

34600 SOLON RD
SOLON, OH 44139-2631
US

Emergency Phone: 216-248-0100

Info Phone: 216-248-0100

Cage: 14045

ERICO PRODUCTS INC

SOLON, OH 44139-2631 US

Telephone: 216-248-0100

Cage: 14045

COPPER OXIDE

CAS: 1317-39-1

RTECS: GL8050000

ALUMINUM/COPPER

CAS: 12608-74-1

CALCIUM FLUORIDE

CAS: 14542-23-5

CALCIUM SILICON

CAS: 37236-74-1

TIN

CAS: 7440-31-5

RTECS: XP7320000

ACGIH TLV: 2 MG/M3

ALUMINUM /VANADIUM

CAS: 39458-13-4

COPPER

CAS: 7440-50-8

RTECS: GL5325000

OSHA PEL 1 MG/M3

ACGIH TLV: 1 MG/M3

EPA Report Quantity: 5000 LBS

DOT Report Quantity: 5000 LBS

Routes of Entry: Inhalation:YES Skin:NO Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:BURNS FROM CONTACT WITH REACTION OR
REACTION PRODUCTS, OR FROM HOT EQUIPMENT. DUST & FUMES ARE ITTITANT
TO EYES & UPPER RESPIRATORY TRACT. INHALATION OF HIGH
CONCENTRATIONS OF FRESHLY FORMED OXIDE FUM ES & DUSTS IN THE
RESPIRABLE PARTICLE SIZE RANGE CAN CAUSE INFLUENZA-LIKE ILLNESS
TERMED METAL FUME FEVER. COPPER XIDE DUST MAY BY REPEATED OR
PROLONGED INHALATION OCCASIONALLY CAUSE ULCERATION & PERF ORATION
OF THE NASAL SEPTUM. LONG TERM EXPOSURE TO COPPER CONTAINING DUST
MAY CAUSE ALLERGIC DERMATITIS. REPEATED EXPOSURE TO EXCESSIVE
CONCENTRATIONS OF FLUORIDES OVER A PERIODS OF YEARS CAN CAUSE FL
UOROSIS.
Effects of Overexposure:SEE HEALTH HAZARDS.

First Aid:STANDARD TREATMENT FOR BURNS IN EVENT OF CONTACT WITH MOLTEN
METAL, SLAG, OR HOT EQUIPMENT. FOR INHALATION OF DUST, FUME, REMOVE
FROM EXPOSURE, PROVIDE FRESH AIR, FLUSH EYES WITH WATER, CONSULT
PHYSIC IAN.

Extinguishing Media:DRY SAND OR FLOODING WITH LARGE AMOUNTS OF WATER.
Unusual Fire/Explosion Hazard:SELF PROPAGATING HIGH TEMPERATURE
REACTION WILL OCCUR IF HEATED ABOVE IGNITION (FLASH POINT)
TEMPERATURE. GENERATES MOLTEN METAL, SLAG, AND DENSE DUSTY SMOKE.
VOLATILE, COMBUSTIBLE DECOMPOSITION PRODU CTS PRODUCED FROM PLASTIC
PACKAGING.

Spill Release Procedures:ALL UNUSED, SPILLED MATERIALS MAY BE SWEPT UP
FOR DISPOSAL, IN ACCORDNACE WITH METHODS OUTLINED, AND FEDERAL,
STATE AND LOCAL REGULATIONS.

Handling and Storage Precautions:MATERIAL SHOULD BE KEPT DRY AND STORED
IN "NO SMOKING OR OPEN FLAME" AREA. RESTRICTION TO AUTHORIZED
PERSONNEL IS RECOMMENDED.
Other Precautions:FOR ADDITIONAL INFORMATION, SEE AMERICAN NATIONAL
STANDARD, SAFETY IN WELDING & CUTTING, Z49.1 AND INSTRUCTIONS
PROVIDED WITH MOLDS.

Respiratory Protection:NORMAL USE PRECLUDES USE OF SPECIAL PROTECTION
AS MATERIAL IS GENERALLY USED OUT OF DOORS, IN SMALL QUANTITIES,
AND IS OF SHORT DURATION.
Ventilation:LOCAL EXHAUST - MAY BE NECESSARY IF USED IN CONFINED SPACE.
SPECIAL - USE OF NIOSH APPROVED RESPIRATOR FOR DUSTS & METAL FUMES
IN LIEU OF LOCAL EXHAUST.
Protective Gloves:RECOMMENDED FOR HANDLING HOT EQUIPMENT.
Eye Protection:SAFETY GLASSES RECOMMENDED.
Supplemental Safety and Health
THIS PRODUCT CONTAINS 80 TO 90 PERCENT COPPER AND COPPER COMPOUNDS,
WHICH ARE SUBJECT TO REPORTING REQUIREMENTS OF SECTION 313 OF TITLE
III OF SARA AND 40 CFR 372.

HCC:N1
Melt/Freeze Pt:=1093.3C, ######F
Spec Gravity:5.5 ((H20=1)
Solubility in Water:INSOLUBLE
Appearance and Odor:GRAY-BLACK GRANULAR PARTICLES, ODORLESS.

Stability Indicator/Materials to Avoid:YES
POSSIBILITY OF VIOLENT REACTION IF MOISTURE PRESENT IN MOLDS OR BASE
MATERIALS BEING WELDED AT TIME OF USE. TYPICAL OF PROBLEMS
ASSOCIATED WITH MOLTEN METALS.
Stability Condition to Avoid:TEMPERATURES ABOVE IGNITION (FLASH POINT).
Hazardous Decomposition Products:NONE
Conditions to Avoid Polymerization:WILL NOT OCCUR

Waste Disposal Methods:1. BURIAL IN GROUND, AFTER SUBMERGING IN MIXTURE
OF SAND & WATER (CONTACT FACTORY). 2. DISPOSAL BY REACTION OF
CONTROLLED QUANTITIES UNDER CONTROLLED CONDITIONS (CONTACT
FACTORY).

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.

SARA Title III Information:THIS PRODUCT CONTAINS 80%-90% COPPER AND
COPPER COMPOUNDS, WHICH ARE SUBJECT TO REPORTING REQUIREMENTS OF
SECTION 313 OF TITLE III OD SARA AND 40 CFR 372.